JewelleryMakingGuide, Biżuteria projekty
[ Pobierz całość w formacie PDF ]
Basic Guide to Jewellery Making
Making Loops for Jewellery
using Eyepins and Headpins
1
2
1
Thread your chosen beads onto a headpin.
2
Cut about 1cm above the beads.
3
Using flat nose pliers bend wire to a right angle.
4
Keep hold of wire with flat nose pliers and using round nose pliers
bend the end into a loop.
5
Use the same technique with eye pins to create a chain of beads effect.
This can be used to make simple earrings, or on bracelets and necklaces.
3
4
5
Using Tiger Tail or Beadalon
for Necklaces and Bracelets
1
2
1
Measure the length of cord you need, leaving about 20cm extra.
Thread your crimp onto the end followed by a clasp.
2
Thread back through the crimp to form a loop around the clasp.
3
Using pliers slide the crimp up to the clasp leaving a tiny excess
for movement. Squash flat with flat-nose pliers/crimping tool.
4
Thread your beads followed by another crimp and the other side of
your clasp. Pull the thread back through the second crimp and two
or three beads and pull tight with pliers before squashing the crimp
and cutting off the excess thread.
3
4
Using Monofilament, Nymo or Silamide
for Necklaces and Bracelets
1
1
Tie a knot in one end of string, add calotte and close cup around the knot
(make sure your knots are big enough so they don't come through the
hole in the calotte).
2
Add your beads and the other calotte with the cups open towards the
free end of thread.
3
Tie a knot loosely and using a pin pull the knot down into the calotte
(make sure your knots are big enough so they don't come through the
hole in the calotte).
4
Close cups and simply add clasp to loop on calotte.
2 3 4
Using Stretch Magic to
make a Bracelet
A
B
1
Cut bracelet length of stretch magic, plus 20cm excess.
2
Thread beads and finish with either of these knots:
A - Overhand Knot
See diagram. You may tighten the bracelet by pulling the two
free threads apart.
B - Dressmaker's Double Knot
Tie an ordinary knot - one thread over the other, then swap the
threads over before repeating to make your double knot.
www.creativebeadcraft.co.uk beads@creativebeadcraft.co.uk
Making a Slip Knot for Pendants
with Leather or Cotton Cord
1
1
Tie the right end around the left strand and the left end around the right strand.
You may now adjust the necklace or bracelet to the size you wish. This is especially
good for pulling necklaces over the head or getting hands through bracelets.
Using Leather and Cotton Cord
to Finish Jewellery
1mm option
A Using a spring end (JF87A)
1
Thread on the beads as required.
2
Take a spring end (JF87A), feed the end of the thong into the spring
and squeeze the last coil tight using a pair of pliers to secure.
3
If you are using 1mm thong double the end over before inserting
into the spring end.
1
2
B Using a cord end (JF123)
Insert the cord into the cord end and squeeze the sides closed with pliers.
3
Jewellery Findings
Earring Fittings
Headpins & Eyepins
Pliers
JF21
JF12
JF57
(Pierced Fittings)
JF54
(Non-Pierced)
S115
Round Nose
Pliers for
making loops
Necklace Ends
JF18/19
Headpins for making
drop earrings by
threading with beads
JF80/20
Eyepins for threading
beads onto and
attaching to other pins
S19
Flat Nose Pliers
for closing
jump rings
CALOTTES
SPRING ENDS
CRIMP BEAD
Actual
Size
Jump Rings
JF55
JF60
JF87A JF123
JF79
S127
Crimping
Pliers
Clasps
JF14
9mm
JF15
7mm
JF16
5mm
JF17
4.5mm
Actual
Size
How to open a jump ring to retain
the shape and strength
S116
Cutters
JF4
JF6
JF84A
JF2
7 mm
JF75
JF13
www.creativebeadcraft.co.uk beads@creativebeadcraft.co.uk
[ Pobierz całość w formacie PDF ]